How to paint ATV plastics ?

9 Steps on How to paint ATV plastics – A DIY Guide

ATV plastics are designed to keep your vehicle away from dusts and dirts while driving in the mud trails. Being an ATV rider enthusiast, there would definitely be a though which will come across to paint your ATV plastics and give them more of your personal touch.
You also will then start questioning on how to paint ATB plastics ? Which paints will stick for a long time on your ATV? The following guide will try to cover all the aspects of ATV plastics painting. If you think on some other ways or improvements, do drop us a comment below.

Let me tell you that paining ATVs on your own is not very difficult DIY process as it sounds. If the right tools are in place and these tools can be utilised properly then painting your ATV become more of a fun.

  • Tools needed to paint ATV plastics
    Sandpaper
    Soft Cloth
    Paint specific Adhesives
    Primer
    Decent urethane for spraying plastic
    Car wax

 

 

Removal off plastic or Decals

First and foremost , you need to remove any plastics around the area or any decals which are there.

Clean the ATV plastics

The first step is to clean the plastic. You can use any soft cloth to first remove the dusts/dirts which are available.
Next , with the help of 180 or 600 grit sandpaper ,sand the entire area . There will be thing curst that gets formed which needs to be removed from sanding process.

Get rid off water-soluble particles

Now it is time to remove any particles that are soluble. You can use scuff magic or red scuff pad, that will remove any water soluble contaminants.

Remove any more crusts present

Using the above mentioned sand paper , you need to sand again to remove any spots left or missed in first place. Once this is done , you need to sanblast everything and cover almost all the area that needs to be painted. You can use 8- grit aluminium oxide for this.The reason sanding is important is because it cleans the deep crusts or patches which if ignored can give a bad look to whole area after it be painted.

Cleaning plastic

Next , you need to clean your plastics with plastic cleaner. You can use polyvalence plastic cleaner. Once spraying is done you need to wait for at least 20 seconds just to make sure the solvents are dissolved properly. Once this is done, you can wipe the surface with soft cloth or any paper towel.

Adhesives and Primer

Finally after thorough cleaning of the surface , you now need to apply adhesives so that the paint gets well sticked with the plastics. You can apply any industrial level adhesives and apply two coats of it. Make sure the first coat is dried well , before applying the second coat. You can use something like plastic magic as adhesives to this process.
Further in order to get the right adhesives, you can get products like Bulldog Tie Coat or Ajax from the stores or order it online which are considered as good bonding agent.

Next , you need to apply primer. Again you need to make sure that the adhesives are already dried off. You can now apply any water resistant primer surfacer. This primer will fill any sandblast pits or scratches. You can apply at least 1-2 coatings of primer.

Sanding


Any imperfections done in above steps can be eliminated by applying Putty flex. Once the putty is dried , it is time to sand again. To get the finishing for the plastic surface , you need to sand the areas again. This is to make the surface is smooth.
Once the sanding process is done, you need to apply waterborne all seasons Bumper sealer and let it dry. This is the last step after which paint layer can be applied.

Painting the ATV Plastic : Best way to paint ATV Plastics

Finally after you have followed all the above steps/methods, now it is time to paint the plastic. You can choose any best paint for atv plastic .So go ahead and start applying the paint. You can use best spray paint for atv plastic available as well. First apply a single layer of paint let it dry off , then apply another layer of the paint to double coat it. Once the double coat painting is done, you need to make sure the top layer is applied with flex additive so as to make sure there is better adhesion between the paints and plastics.
Let it dry off again.

Waxing the surface

Once the paint is done , you can apply any car wax to shine the plastic further.Further if you have following the above DIY methods, finally you have answered your question on How to Paint ATV plastics

The process is bit lengthy but once you are done the end result is definitely going to make you happy.

 

Read Related Posts ⁄